Vulnerabilities > Linux > Linux Kernel > 3.4.104
| DATE | CVE | VULNERABILITY TITLE | RISK |
|---|---|---|---|
| 2025-04-02 | CVE-2025-21993 | Out-of-bounds Read vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: iscsi_ibft: Fix UBSAN shift-out-of-bounds warning in ibft_attr_show_nic() When performing an iSCSI boot using IPv6, iscsistart still reads the /sys/firmware/ibft/ethernetX/subnet-mask entry. | 7.1 |
| 2025-04-01 | CVE-2025-21912 | Improper Locking vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: gpio: rcar: Use raw_spinlock to protect register access Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. | 5.5 |
| 2025-04-01 | CVE-2025-21917 | NULL Pointer Dereference vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: usb: renesas_usbhs: Flush the notify_hotplug_work When performing continuous unbind/bind operations on the USB drivers available on the Renesas RZ/G2L SoC, a kernel crash with the message "Unable to handle kernel NULL pointer dereference at virtual address" may occur. | 5.5 |
| 2025-04-01 | CVE-2025-21920 | Out-of-bounds Read vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: vlan: enforce underlying device type Currently, VLAN devices can be created on top of non-ethernet devices. Besides the fact that it doesn't make much sense, this also causes a bug which leaks the address of a kernel function to usermode. When creating a VLAN device, we initialize GARP (garp_init_applicant) and MRP (mrp_init_applicant) for the underlying device. As part of the initialization process, we add the multicast address of each applicant to the underlying device, by calling dev_mc_add. __dev_mc_add uses dev->addr_len to determine the length of the new multicast address. This causes an out-of-bounds read if dev->addr_len is greater than 6, since the multicast addresses provided by GARP and MRP are only 6 bytes long. This behaviour can be reproduced using the following commands: ip tunnel add gretest mode ip6gre local ::1 remote ::2 dev lo ip l set up dev gretest ip link add link gretest name vlantest type vlan id 100 Then, the following command will display the address of garp_pdu_rcv: ip maddr show | grep 01:80:c2:00:00:21 Fix the bug by enforcing the type of the underlying device during VLAN device initialization. | 7.1 |
| 2025-04-01 | CVE-2025-21922 | Use of Uninitialized Resource vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: ppp: Fix KMSAN uninit-value warning with bpf Syzbot caught an "KMSAN: uninit-value" warning [1], which is caused by the ppp driver not initializing a 2-byte header when using socket filter. The following code can generate a PPP filter BPF program: ''' struct bpf_program fp; pcap_t *handle; handle = pcap_open_dead(DLT_PPP_PPPD, 65535); pcap_compile(handle, &fp, "ip and outbound", 0, 0); bpf_dump(&fp, 1); ''' Its output is: ''' (000) ldh [2] (001) jeq #0x21 jt 2 jf 5 (002) ldb [0] (003) jeq #0x1 jt 4 jf 5 (004) ret #65535 (005) ret #0 ''' Wen can find similar code at the following link: https://github.com/ppp-project/ppp/blob/master/pppd/options.c#L1680 The maintainer of this code repository is also the original maintainer of the ppp driver. As you can see the BPF program skips 2 bytes of data and then reads the 'Protocol' field to determine if it's an IP packet. | 5.5 |
| 2025-04-01 | CVE-2025-21957 | NULL Pointer Dereference vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: scsi: qla1280: Fix kernel oops when debug level > 2 A null dereference or oops exception will eventually occur when qla1280.c driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. | 5.5 |
| 2025-04-01 | CVE-2025-21969 | Use After Free vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix slab-use-after-free Read in l2cap_send_cmd After the hci sync command releases l2cap_conn, the hci receive data work queue references the released l2cap_conn when sending to the upper layer. Add hci dev lock to the hci receive data work queue to synchronize the two. [1] BUG: KASAN: slab-use-after-free in l2cap_send_cmd+0x187/0x8d0 net/bluetooth/l2cap_core.c:954 Read of size 8 at addr ffff8880271a4000 by task kworker/u9:2/5837 CPU: 0 UID: 0 PID: 5837 Comm: kworker/u9:2 Not tainted 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: hci1 hci_rx_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x169/0x550 mm/kasan/report.c:489 kasan_report+0x143/0x180 mm/kasan/report.c:602 l2cap_build_cmd net/bluetooth/l2cap_core.c:2964 [inline] l2cap_send_cmd+0x187/0x8d0 net/bluetooth/l2cap_core.c:954 l2cap_sig_send_rej net/bluetooth/l2cap_core.c:5502 [inline] l2cap_sig_channel net/bluetooth/l2cap_core.c:5538 [inline] l2cap_recv_frame+0x221f/0x10db0 net/bluetooth/l2cap_core.c:6817 hci_acldata_packet net/bluetooth/hci_core.c:3797 [inline] hci_rx_work+0x508/0xdb0 net/bluetooth/hci_core.c:4040 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Allocated by task 5837: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x243/0x390 mm/slub.c:4329 kmalloc_noprof include/linux/slab.h:901 [inline] kzalloc_noprof include/linux/slab.h:1037 [inline] l2cap_conn_add+0xa9/0x8e0 net/bluetooth/l2cap_core.c:6860 l2cap_connect_cfm+0x115/0x1090 net/bluetooth/l2cap_core.c:7239 hci_connect_cfm include/net/bluetooth/hci_core.h:2057 [inline] hci_remote_features_evt+0x68e/0xac0 net/bluetooth/hci_event.c:3726 hci_event_func net/bluetooth/hci_event.c:7473 [inline] hci_event_packet+0xac2/0x1540 net/bluetooth/hci_event.c:7525 hci_rx_work+0x3f3/0xdb0 net/bluetooth/hci_core.c:4035 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Freed by task 54: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:582 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x59/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2353 [inline] slab_free mm/slub.c:4613 [inline] kfree+0x196/0x430 mm/slub.c:4761 l2cap_connect_cfm+0xcc/0x1090 net/bluetooth/l2cap_core.c:7235 hci_connect_cfm include/net/bluetooth/hci_core.h:2057 [inline] hci_conn_failed+0x287/0x400 net/bluetooth/hci_conn.c:1266 hci_abort_conn_sync+0x56c/0x11f0 net/bluetooth/hci_sync.c:5603 hci_cmd_sync_work+0x22b/0x400 net/bluetooth/hci_sync.c:332 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr ---truncated--- | 7.8 |
| 2025-03-27 | CVE-2022-49738 | Out-of-bounds Read vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on i_extra_isize in is_alive() syzbot found a f2fs bug: BUG: KASAN: slab-out-of-bounds in data_blkaddr fs/f2fs/f2fs.h:2891 [inline] BUG: KASAN: slab-out-of-bounds in is_alive fs/f2fs/gc.c:1117 [inline] BUG: KASAN: slab-out-of-bounds in gc_data_segment fs/f2fs/gc.c:1520 [inline] BUG: KASAN: slab-out-of-bounds in do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 Read of size 4 at addr ffff888076557568 by task kworker/u4:3/52 CPU: 1 PID: 52 Comm: kworker/u4:3 Not tainted 6.1.0-rc4-syzkaller-00362-gfef7fd48922d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Workqueue: writeback wb_workfn (flush-7:0) Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:284 [inline] print_report+0x15e/0x45d mm/kasan/report.c:395 kasan_report+0xbb/0x1f0 mm/kasan/report.c:495 data_blkaddr fs/f2fs/f2fs.h:2891 [inline] is_alive fs/f2fs/gc.c:1117 [inline] gc_data_segment fs/f2fs/gc.c:1520 [inline] do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 f2fs_gc+0x88c/0x20a0 fs/f2fs/gc.c:1831 f2fs_balance_fs+0x544/0x6b0 fs/f2fs/segment.c:410 f2fs_write_inode+0x57e/0xe20 fs/f2fs/inode.c:753 write_inode fs/fs-writeback.c:1440 [inline] __writeback_single_inode+0xcfc/0x1440 fs/fs-writeback.c:1652 writeback_sb_inodes+0x54d/0xf90 fs/fs-writeback.c:1870 wb_writeback+0x2c5/0xd70 fs/fs-writeback.c:2044 wb_do_writeback fs/fs-writeback.c:2187 [inline] wb_workfn+0x2dc/0x12f0 fs/fs-writeback.c:2227 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x665/0x1080 kernel/workqueue.c:2436 kthread+0x2e4/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 The root cause is that we forgot to do sanity check on .i_extra_isize in below path, result in accessing invalid address later, fix it. - gc_data_segment - is_alive - data_blkaddr - offset_in_addr | 7.1 |
| 2025-03-27 | CVE-2022-49740 | Out-of-bounds Read vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the count value of channel spec to prevent out-of-bounds reads This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). | 7.1 |
| 2025-03-27 | CVE-2022-49741 | Memory Leak vulnerability in Linux Kernel In the Linux kernel, the following vulnerability has been resolved: fbdev: smscufx: fix error handling code in ufx_usb_probe The current error handling code in ufx_usb_probe have many unmatching issues, e.g., missing ufx_free_usb_list, destroy_modedb label should only include framebuffer_release, fb_dealloc_cmap only matches fb_alloc_cmap. My local syzkaller reports a memory leak bug: memory leak in ufx_usb_probe BUG: memory leak unreferenced object 0xffff88802f879580 (size 128): comm "kworker/0:7", pid 17416, jiffies 4295067474 (age 46.710s) hex dump (first 32 bytes): 80 21 7c 2e 80 88 ff ff 18 d0 d0 0c 80 88 ff ff .!|............. 00 d0 d0 0c 80 88 ff ff e0 ff ff ff 0f 00 00 00 ................ backtrace: [<ffffffff814c99a0>] kmalloc_trace+0x20/0x90 mm/slab_common.c:1045 [<ffffffff824d219c>] kmalloc include/linux/slab.h:553 [inline] [<ffffffff824d219c>] kzalloc include/linux/slab.h:689 [inline] [<ffffffff824d219c>] ufx_alloc_urb_list drivers/video/fbdev/smscufx.c:1873 [inline] [<ffffffff824d219c>] ufx_usb_probe+0x11c/0x15a0 drivers/video/fbdev/smscufx.c:1655 [<ffffffff82d17927>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396 [<ffffffff82712f0d>] call_driver_probe drivers/base/dd.c:560 [inline] [<ffffffff82712f0d>] really_probe+0x12d/0x390 drivers/base/dd.c:639 [<ffffffff8271322f>] __driver_probe_device+0xbf/0x140 drivers/base/dd.c:778 [<ffffffff827132da>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:808 [<ffffffff82713c27>] __device_attach_driver+0xf7/0x150 drivers/base/dd.c:936 [<ffffffff82710137>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427 [<ffffffff827136b5>] __device_attach+0x105/0x2d0 drivers/base/dd.c:1008 [<ffffffff82711d36>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487 [<ffffffff8270e242>] device_add+0x642/0xdc0 drivers/base/core.c:3517 [<ffffffff82d14d5f>] usb_set_configuration+0x8ef/0xb80 drivers/usb/core/message.c:2170 [<ffffffff82d2576c>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238 [<ffffffff82d16ffc>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293 [<ffffffff82712f0d>] call_driver_probe drivers/base/dd.c:560 [inline] [<ffffffff82712f0d>] really_probe+0x12d/0x390 drivers/base/dd.c:639 [<ffffffff8271322f>] __driver_probe_device+0xbf/0x140 drivers/base/dd.c:778 Fix this bug by rewriting the error handling code in ufx_usb_probe. | 5.5 |